Recycling of wastes and their by-products is attracting increasing interest worldwide because of the high environmental impact in the cement, concrete and other industries. This work deals with the study of the physico-chemical characteristics of binders based on sewage sludge ashes and lime. In a first step, we used X-ray fluorescence to determine the chemical composition of ash, lime and binders. This allowed us to see that the chemical composition of sewage sludge ash is similar to that of cement. We then used X-ray diffraction to identify the main mineralogical phases in the samples. Compressive strengths of mortars containing 20%, 40%, 60% and 80% of SSA showed that SSA has a long-term positive effect which might be related to a slight pozzolanic activity. The L4 binder consisting of 80% fine ash and 20% lime has a higher compressive strength than the others. The binder setting start time is greater than that of cement but shorter than that of lime. The study of the thermophysical properties of the L4 binder shows that it has a higher thermal resistance than cement and clay mortars. Moreover, it heats up less quickly because of its low effusivity compared to the latter two. This analysis highlighted the principal characteristics that must be taken into account to use SSA correctly in lime-based materials.
| Published in | Advances in Materials (Volume 10, Issue 2) |
| DOI | 10.11648/j.am.20211002.11 |
| Page(s) | 12-22 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2021. Published by Science Publishing Group |
Sewage Sludge Ash, Lime, Binder, X-ray Fluorescence, X-ray Diffraction, Thermomechanical Behavior
| [1] | M. Cyr, G. Klysz, S. Julien and P. Clastres, «Les cendres d'incinération de boues de stations de traitement des eaux polluées sont-elles utilisablesdans les matrices cimentaires? comparaison avec les cendres volantes de charbon,» revue francophone d’écologie industrielle, pp. 22-29, 2003. |
| [2] | EUROSTAT, «http://epp.eurostat.cec.eu.int », 2005. |
| [3] | S. Pan, D. Tseng, C. Lee and C. Lee, «Influence of the fineness of sewage sludge ash on the mortar properties,» Cement and Concrete Research, pp. 1749-1754, 2003. |
| [4] | S. Badur and R. Chaudhary, ««Utilization of hazardous wastes and by-products as a green concrete material through S/S process:» A review». Rev. Adv. Mater. Sci, Vols. %1 sur %217, pp. 42-61, 2008. |
| [5] | W. Piasta and M. Lukawska, «The Effect of Sewage Sludge Ash on Properties of Cement Composites,» Procedia Engineering, pp. 1018-1024, 2016. |
| [6] | M. Cyr, M. Coutand and P. and Clastres, «Technological and environmental behavior of sewage sludge ash (SSA) in cement-based materials.,» Cem. Concr. Res., pp. 1278-1289, 2007. |
| [7] | S. Donatello et C. R. Cheeseman, «Recycling and recovery routes for incinerated sewage sludge ash (ISSA): A review,» Waste Management, p. 2328–2340, 2013. |
| [8] | C. Lynn, R. Dhir, G. West and R. Ghataora, «Sewage sludge ash characteristics and potential for use in concret,» Conccrete and Building Materials, pp. 767-779, 2015. |
| [9] | J. Tay and K. Show, «Municipal wastewater sludge as cementitious and blended cement materials,» Cement and Concrete Composites., vol. 16, pp. 39-48, 1994. |
| [10] | S. Pan, «Use of sewage sludge ash as fine aggregate and pozzolan in portland cement mortar,» Journal of Solid Waste Technology and Management, vol. 28, pp. 121-130, 2002. |
| [11] | OECD, ««Organization for economic co-operation and development»,»: http://www.oecd.org/fr/ https://data.oecd.org/fr/, 2017. |
| [12] | P. J. Potts, O. Williams-Thorpe and P. Webb, «The Bulk Analysis of Silicate Rocks by Portable X-Ray Fluorescence: Effect of Sample Mineralogy in Relation to the Size of the Excited Volume,» The Journal of Geostandards and Geoanalysis, pp. 29-41, 1997. |
| [13] | M. Chen, D. Blanc, M. Gautier, J. Mehu and R. Gourdon, «Environmental and technical assessments of the potential utilization of sewagesludge ashes (SSAs) as secondary raw materials in construction,» Waste Management, pp. 1268-1275, 2013. |
| [14] | R. Rajamma, R. Ball, L. Tarelho, G. Allen, J. Ferreira and V. Labrincha, «Characterisation and use of biomass fly ash in cement-based materials,» J Hazard Mater, pp. 1049-60, 2009. |
| [15] | V. Somerset, L. Petrik, R. White, M. Klink, D. Key and E. Iwuoha, «The use of X-ray fluorescence (XRF) analysis in predicting the alkaline hydrothermal conversion of fly ash precipitates into zeolites,» Talanta, pp. 109-114, 2004. |
| [16] | H. Bal, Y. Jannot, N. Quenette and A. Chenu, «Water content dependence of the porosity, density and thermal capacity of laterite based bricks with millet waste additive.,» Construction and Buildings Materials., p. 144–150, 2012. |
| [17] | Y. Jannot, V. Felix and A. Degiovanni, «A centered hot plate method for measurement of thermal properties of thin insulating materials.,» Measurement Science And Technology, p. 1–8, (2010). |
| [18] | K. Neupane, «Fly ash and GGBFS based powder-activated geopolymer binders: Aviable sustainable alternative of portland cement in concrete industry,» Mechanics of Materials, vol. 103, pp. 110-122, 2016. |
| [19] | M. Coo and T. Pheeraphan, «Effect of sand, fly ash and limestone powder on preplaced aggregate concrete mechanical properties and reinforced beam shear capacity,» Construction and Building Materials, vol. 120, p. 581–592, 2016. |
| [20] | K. Turk, C. Kina and M. Bagdiken, «Use of binary and ternary cementitious blends of F-Class fly-ash and limestone powder to mitigate alkali-silica reaction risk,» Construction and Building Materials, vol. 151, p. 422–427, 2017. |
| [21] | S. Chin, D. Ing, A. Kusbiantoro, Y. Wong and S. Ahmad, «Characterization of sewage sludge ASH (SSA) in cement mortar,» ARPN J. Eng. Appl. Sci, vol. 11, pp. 2242-2247, 2016. |
| [22] | M. Sall, P. Gueye, A. Traore, S. Diouf, M. Sy, G. Bouchez, A. Wade, M. Sane, G. Dieye and D. Diop, «Assessment of Fine and Coarse Sewage Sludge Ashes forTheir Potential Use in Civil Engineering,» Journal of Civil, Construction and Environmental Engineering, vol. 5, n° 14, pp. 99-106, 2020. |
| [23] | M. Coutand, M. Cyr and P. Clastres, «Use of sewage sludge ash as mineral admixture in mortars,» Construction Materials, pp. 153-162, 2006. |
| [24] | W. Xu, J. Xu, J. Liu, H. Li, B. Cao, X. Huang and G. Li, «The utilization of lime dried sludge as resource for producing cement,» Journal of Cleaner Production, pp. 286-293, 2014. |
| [25] | N. H. Rodríguez, S. Ramírez, B. Varela, S. Donatello, M. Guillem, J. Puig, C. Fos, E. Flores and J. Larrotcha, «The effect of using thermally dried sewage sludge as an alternative fuel on Portland cement clinker production,» Journal of Cleaner Production, pp. 94-102, 2013. |
| [26] | J. Xiao, C. Gou, Y. Yin and Y. Wang, «Effect of CaCO3 on hydration characteristics of C3A,» Journal of Central South university of Technology, pp. 918-923, 2010. |
| [27] | T. Sato and J. Beaudoin, «Effect of nano-CaCO3 on hydration of cement containing supplementary cementitious materials,» Advances in Cement Research, vol. 23, n° %11, pp. 33-43, 2011. |
| [28] | P. Garcés, M. Carrión, E. Alcocel, J. Payá, J. Monzó and M. Borrachero, «Mechanical and physical properties of cement blended with sewage sludge ash,» Waste Management 2495–2502, pp. 2495-2502, 2008. |
| [29] | T. Dyer, R. Dhir and J. Haliday, «Hydration Chemistry of Sewage Sludge Ash Used as a Cement Component,» Journal of Materials in Civil Engineering, pp. 648-655, 2011. |
| [30] | G. Arliguie, J. Ollivier and J. Grandet, «Etude de l'effet retardateur du zinc sur l'hydratation de la pate de ciment portland,» cement and concrete research., vol. 12, pp. 79-86, 1982. |
| [31] | K. Marti, «Catalogue d’éléments de construction avec calcul de la valeur U,» Office fédéral de l'énergie, 2002. |
| [32] | N. Laaroussi, A. Cherkia, M. Garoum, A. Khabbazi and A. Feiz, «Thermal Properties of a Sample Prepared Using Mixtures of Clay Bricks», Energy Procedia, p. 337-346, 2013. |
APA Style
Mamoudou Sall, Alassane Traoré, Abdou Ciss Wade, Prince Momar Gueye, Saliou Diouf, et al. (2021). Potential Use of Sewage Sludge Ash in Lime-Based Materials. Advances in Materials, 10(2), 12-22. https://doi.org/10.11648/j.am.20211002.11
ACS Style
Mamoudou Sall; Alassane Traoré; Abdou Ciss Wade; Prince Momar Gueye; Saliou Diouf, et al. Potential Use of Sewage Sludge Ash in Lime-Based Materials. Adv. Mater. 2021, 10(2), 12-22. doi: 10.11648/j.am.20211002.11
AMA Style
Mamoudou Sall, Alassane Traoré, Abdou Ciss Wade, Prince Momar Gueye, Saliou Diouf, et al. Potential Use of Sewage Sludge Ash in Lime-Based Materials. Adv Mater. 2021;10(2):12-22. doi: 10.11648/j.am.20211002.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.am.20211002.11,
author = {Mamoudou Sall and Alassane Traoré and Abdou Ciss Wade and Prince Momar Gueye and Saliou Diouf and Gora Dieye and Djibril Diop},
title = {Potential Use of Sewage Sludge Ash in Lime-Based Materials},
journal = {Advances in Materials},
volume = {10},
number = {2},
pages = {12-22},
doi = {10.11648/j.am.20211002.11},
url = {https://doi.org/10.11648/j.am.20211002.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.am.20211002.11},
abstract = {Recycling of wastes and their by-products is attracting increasing interest worldwide because of the high environmental impact in the cement, concrete and other industries. This work deals with the study of the physico-chemical characteristics of binders based on sewage sludge ashes and lime. In a first step, we used X-ray fluorescence to determine the chemical composition of ash, lime and binders. This allowed us to see that the chemical composition of sewage sludge ash is similar to that of cement. We then used X-ray diffraction to identify the main mineralogical phases in the samples. Compressive strengths of mortars containing 20%, 40%, 60% and 80% of SSA showed that SSA has a long-term positive effect which might be related to a slight pozzolanic activity. The L4 binder consisting of 80% fine ash and 20% lime has a higher compressive strength than the others. The binder setting start time is greater than that of cement but shorter than that of lime. The study of the thermophysical properties of the L4 binder shows that it has a higher thermal resistance than cement and clay mortars. Moreover, it heats up less quickly because of its low effusivity compared to the latter two. This analysis highlighted the principal characteristics that must be taken into account to use SSA correctly in lime-based materials.},
year = {2021}
}
TY - JOUR T1 - Potential Use of Sewage Sludge Ash in Lime-Based Materials AU - Mamoudou Sall AU - Alassane Traoré AU - Abdou Ciss Wade AU - Prince Momar Gueye AU - Saliou Diouf AU - Gora Dieye AU - Djibril Diop Y1 - 2021/06/15 PY - 2021 N1 - https://doi.org/10.11648/j.am.20211002.11 DO - 10.11648/j.am.20211002.11 T2 - Advances in Materials JF - Advances in Materials JO - Advances in Materials SP - 12 EP - 22 PB - Science Publishing Group SN - 2327-252X UR - https://doi.org/10.11648/j.am.20211002.11 AB - Recycling of wastes and their by-products is attracting increasing interest worldwide because of the high environmental impact in the cement, concrete and other industries. This work deals with the study of the physico-chemical characteristics of binders based on sewage sludge ashes and lime. In a first step, we used X-ray fluorescence to determine the chemical composition of ash, lime and binders. This allowed us to see that the chemical composition of sewage sludge ash is similar to that of cement. We then used X-ray diffraction to identify the main mineralogical phases in the samples. Compressive strengths of mortars containing 20%, 40%, 60% and 80% of SSA showed that SSA has a long-term positive effect which might be related to a slight pozzolanic activity. The L4 binder consisting of 80% fine ash and 20% lime has a higher compressive strength than the others. The binder setting start time is greater than that of cement but shorter than that of lime. The study of the thermophysical properties of the L4 binder shows that it has a higher thermal resistance than cement and clay mortars. Moreover, it heats up less quickly because of its low effusivity compared to the latter two. This analysis highlighted the principal characteristics that must be taken into account to use SSA correctly in lime-based materials. VL - 10 IS - 2 ER -
Email: